
Installation & Routers
Understand the steps, prepare your home and connect your router. Your setup depends on the connection available at your address and the details confirmed in your order.
Your confirmed order details determine your appointment and equipment. You can browse this guide without signing in.
How a Full Fibre connection fits together
Illustrative only — your actual equipment depends on your order.
Part Fibre (SOGEA) connects through your local access line and socket instead of an ONT.
Your exact installation depends on your address and order
This page explains how installation and setup generally work. We'll never show an appointment as booked, a router as included, installation as free, or self-install as available until your own order confirms it. Diagrams here are illustrative.
Which connection are you getting?
Pick the connection type to see the right installation guidance. Not sure yet? Check your address — the connection available decides which applies.
Full Fibre (FTTP)
Fibre runs to the premises where it's provisioned. Uses an ONT indoors, connected to your router.
Steps may vary by property.
Part Fibre (SOGEA)
Uses your local access line and socket. Not an analogue voice product — a traditional landline isn't included by default.
Socket and setup may vary.
Not sure which connection?
The connection available at your property decides this. Check your address and we'll show what applies.
No address is stored to browse this guide.
Four steps from order to online
A simple overview of what to expect. Each step links to more detail further down the page.
Check your connection
See what's available at your address and which installation may apply.
Prepare your home
Think about equipment placement, power sockets and any permissions if you rent.
Connect your equipment
Link your ONT or socket to your router with the supplied cables, then power it on.
Confirm service works
Follow your activation guidance, check the lights and test that you're online.
How your installation works
Pick a connection type. An engineer visit or wall work may be needed for some homes — we'll confirm the steps relevant to your order.
Full Fibre (FTTP) installation
The fibre service at your property connects to an ONT indoors, which connects to your router. The ONT is separate from your router.
Check the route
Check your address to see what installation may be needed. Availability is address-specific.
Get ready
You may need to agree where equipment and fibre enter your home. If you rent, check permission in advance.
Engineer work (if required)
Where a visit is required, the engineer may bring a fibre cable into the property and install or use an ONT.
Connect your router
Connect the ONT to your router using the cable and instructions supplied for your actual equipment.
Activate and check
Follow your activation message, verify the lights and test the connection.
The FTTP equipment chain
- 1.
External network connection — an external fibre route may connect your property to the network.
- 2.
Fibre cable — connects the outside network to the indoor termination point.
- 3.
Optical Network Terminal (ONT) — the indoor equipment that terminates the fibre.
- 4.
Ethernet cable — connects the ONT to the router's WAN port, where applicable.
- 5.
Broadband router — distributes the connection over Wi-Fi and Ethernet.
- 6.
Devices — laptops, phones, TVs and other equipment connect to the router.
Illustrative. An engineer visit or wall work may be needed for some homes.
Setting up your router
Follow the guide supplied with your actual equipment. Port labels and lights vary by model — these steps are the general shape of it.
Before you power on
Find the power adapter and the correct broadband cable. Use only the instructions supplied for your device.
Connect the equipment
Connect each cable to the labelled port. For Full Fibre, the ONT connects to the router's WAN port.
Wait for activation
Status lights vary by model. Your connection may not start the moment you switch on — follow your confirmation.
Connect a device
Select your Wi-Fi network and enter the credentials from your router label or approved account process.
Verify you're online
Open a familiar website. If it loads, you're connected. If not, try the troubleshooting steps below.
Where to place your router
Put it on a stable, ventilated surface, off the floor and away from thick walls, TVs and other electronics. Keep vents clear and use a suitable mains socket. Walls, distance and many connected devices all affect Wi-Fi coverage.
Reboot vs factory reset
A reboot (power off, wait, power on) is safe and fixes many glitches. A factory reset wipes your settings and should only be done with the approved instructions for your model — it's not a quick fix. When in doubt, contact support.
Preparing for an engineer
If your order needs a visit, a little preparation helps it go smoothly. Tick these off as you go — nothing here is saved to an account.
Need to change your appointment?
To change a confirmed appointment, use Track Your Order or contact support. If more work is needed, we'll explain the next steps through your order updates.
What are you having trouble with?
Pick the closest symptom for safe checks to try. If your service should be live and still isn't, we'll point you to support — we won't assume it's your fault.
Installation & router FAQs
Still need a hand?
Our UK-based team can help before, during and after your installation. Your confirmed order is always the source of truth for dates and equipment.
Visit the Help Centre
Related pages
Check what's available at your address
See which connection and installation apply where you live. We only use your postcode and selected address to check availability — no account is required to browse this guide.
Checking availability doesn't create an order. We'll never show an appointment or equipment as confirmed until your order does.
